7
如何实现CentOS服务器的扩容??
source link: https://segmentfault.com/a/1190000039001121
Go to the source link to view the article. You can view the picture content, updated content and better typesetting reading experience. If the link is broken, please click the button below to view the snapshot at that time.
Linux的硬盘识别:
一般使用”fdisk -l”命令可以列出系统中当前连接的硬盘
设备和分区信息.新硬盘没有分区信息,则只显示硬盘大小信息.
1.关闭服务器加上新硬盘
2.启动服务器,以root用户登录
3.查看硬盘信息
#fdisk -l Disk /dev/sda: 42.9 GB, 42949672960 bytes 255 heads, 63 sectors/track, 5221 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004406e Device Boot Start End Blocks Id System /dev/sda1 * 1 39 307200 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 39 2589 20480000 83 Linux /dev/sda3 2589 2850 2097152 82 Linux swap / Solaris /dev/sda4 2850 5222 19057664 5 Extended /dev/sda5 2850 5222 19056640 83 Linux Disk /dev/sdb: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x14b52796 Device Boot Start End Blocks Id System
4.创建新硬盘分区命令参数:
fdisk可以用m命令来看fdisk命令的内部命令; a:命令指定启动分区; d:命令删除一个存在的分区; l:命令显示分区ID号的列表; m:查看fdisk命令帮助; n:命令创建一个新分区; p:命令显示分区列表; t:命令修改分区的类型ID号; w:命令是将对分区表的修改存盘让它发生作用5.进入磁盘,对磁盘进行分区,注意红色部分。
#fdisk /dev/sdb Command (m for help):n Command action e extended //输入e为创建扩展分区 p primary partition (1-4) //输入p为创建逻辑分区 p Partion number(1-4):1 //在这里输入l,就进入划分逻辑分区阶段了; First cylinder (51-125, default 51): //注:这个就是分区的Start 值;这里最好直接按回车,如果您输入了一个非默认的数字,会造成空间浪费; Using default value 51 Last cylinder or +size or +sizeM or +sizeK (51-125, default 125): +200M 注:这个是定义分区大小的,+200M 就是大小为200M ;当然您也可以根据p提示的单位cylinder的大小来算,然后来指定 End的数值。回头看看是怎么算的;还是用+200M这个办法来添加,这样能直观一点。如果您想添加一个10G左右大小的分区,请输入 +10000M ; Command (m for help): w //最后输入w回车保存。
查看一下:
#fdisk -l
可以看到/dev/sdb1分区,我就省略截图咯。
6.格式化分区:
#mkfs.ext3 /dev/sdb1 //注:将/dev/sdb1格式化为ext3类型 mke2fs 1.41.12 (17-May-2010) 文件系统标签= 操作系统:Linux 块大小=4096 (log=2) 分块大小=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 640848 inodes, 2562359 blocks 128117 blocks (5.00%) reserved for the super user 第一个数据块=0 Maximum filesystem blocks=2625634304 79 block groups 32768 blocks per group, 32768 fragments per group 8112 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632 正在写入inode表: 完成 Creating journal (32768 blocks): 完成 Writing superblocks and filesystem accounting information: 完成 This filesystem will be automatically checked every 35 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override.
这样就格式化好了,我们就可以用mount 加载这个分区,然后使用这个文件系统;
7.创建/data1目录:
#mkdir /data1
8.开始挂载分区:
#mount /dev/sdb1 /data1
9.查看硬盘大小以及挂载分区:
#df -h
10.配置开机自动挂载
因为mount挂载在重启服务器后会失效,所以需要将分区信息写到/etc/fstab文件中让它永久挂载:
#vim /etc/fstab
加入:
/dev/sdb1(磁盘分区) /data1(挂载目录) ext3(文件格式)defaults 0 0
11.重启系统
Recommend
About Joyk
Aggregate valuable and interesting links.
Joyk means Joy of geeK